[Vintage] World Trade Center Construction Promo (1968-1972)

I found this video on some old internet archive site in late 2012. At the time of their completion, the “Twin Towers“ — the original 1 World Trade Center, at 1,368 feet (417 m); and 2 World Trade Center, at 1,362 feet (415 m) — were the tallest buildings in the world. The other buildings in the complex included the Marriott World Trade Center (3 WTC), 4 WTC, 5 WTC, 6 WTC, and 7 WTC. All these buildings were built between 1975 and 1985, with a construction cost of $400 million ($2,300,000,000 in 2014 dollars).[4] The complex was located in New York City’s Financial District and contained 13,400,000 square feet (1,240,000 m2) of office space.[5][6] On September 20, 1962, the Port Authority announced the selection of Minoru Yamasaki as lead architect and Emery Roth & Sons as associate architects.[32] Yamasaki devised the plan to incorporate twin towers; Yamasaki’s original plan called for the towers to be 80 stories tall,[33] but to meet the Port Authority’s requirement for 10,000,000 square feet (930,000 m2) of office space, the buildings would each have to be 110 stories tall.[34] Yamasaki’s design for the World Trade Center, unveiled to the public on January 18, 1964, called for a square plan approximately 208 feet (63 m) in dimension on each side.[33][35] The buildings were designed with narrow office windows 18 inches (46 cm) wide, which reflected Yamasaki’s fear of heights as well as his desire to make building occupants feel secure.[36] Yamasaki’s design included building facades sheathed in aluminum-alloy.[37] The World Trade Center was one of the most-striking American implementations of the architectural ethic of Le Corbusier, and it was the seminal expression of Yamasaki’s gothic modernist tendencies.[38] A major limiting factor in building height is the issue of elevators; the taller the building, the more elevators are needed to service the building, requiring more space-consuming elevator banks.[34] Yamasaki and the engineers decided to use a new system with two “sky lobbies“—floors where people could switch from a large-capacity express elevator to a local elevator that goes to each floor in a section. This system, inspired by the local-express train operation that the New York City Subway system used,[39] allowed the design to stack local elevators within the same elevator shaft. Located on the 44th and 78th floors of each tower, the sky lobbies enabled the elevators to be used efficiently, increasing the amount of usable space on each floor from 62 to 75 percent by reducing the number of elevator shafts.[40][41] Altogether, the World Trade Center had 95 express and local elevators.[42] The structural engineering firm Worthington, Skilling, Helle & Jackson worked to implement Yamasaki’s design, developing the tube-frame structural system used in the twin towers. The Port Authority’s Engineering Department served as foundation engineers, Joseph R. Loring & Associates as electrical engineers, and Jaros, Baum & Bolles (JB&B) as mechanical engineers. Tishman Realty & Construction Company was the general contractor on the World Trade Center project. Guy F. Tozzoli, director of the World Trade Department at the Port Authority, and Rino M. Monti, the Port Authority’s Chief Engineer, oversaw the project.[43] As an interstate agency, the Port Authority was not subject to local laws and regulations of the City of New York, including building codes. Nonetheless, the structural engineers of the World Trade Center ended up following draft versions of the new 1968 building codes.[44] The tube-frame design, earlier introduced by Fazlur Khan, was a new approach that allowed more open floor plans than the traditional design that distributed columns throughout the interior to support building loads. The World Trade Center towers used high-strength, load-bearing perimeter steel columns called Vierendeel trusses that were spaced closely together to form a strong, rigid wall structure, supporting virtually all lateral loads such as wind loads, and sharing the gravity load with the core columns. The perimeter structure containing 59 columns per side was constructed with extensive use of prefabricated modular pieces, each consisting of three columns, three stories tall, connected by spandrel plates.[45] The spandrel plates were welded to the columns to create the modular pieces off-site at the fabrication shop.[46] Adjacent modules were bolted together with the splices occurring at mid-span of the columns and spandrels. The spandrel plates were located at each floor, transmitting shear stress between columns, allowing them to work together in resisting lateral loads. The joints between modules were staggered vertically, so that the column splices between adjacent modules were not at the same floor.[44]